FANUC Servo Motors- Get Tested|Repaired|Encoder-Replaced& ReAligned

We Are Available Right Here in UAE to Help you “Preserve Your Investment” in FANUC Servo Motors– by Restoring faulty motors to Working condition & Validating Suspected motors by Run-Test

FANUC Servo Motors are permanent magnet-excited motors with electronic commutation. If you find yourself needing a Repair of your FANUC Servo Motor . or You need to buy a FANUC Servo Motor component (e.g. FANUC Encoders | FANUC Brake | FANUC Connectors etc.) Contact us by mail This email address is being protected from spambots. You need JavaScript enabled to view it.

You may utilize our expert servo Repair services in Scenarios where:

You have a FANUC Servo Motor where you are sure MOTOR FeedbackEncoder is Faulty- We can quickly get you up and running by arranging a New encoder from Stock or Through our Associates around the world, and Replacing it on the motor to get it Working Again. We will Run-Test it so it is ready to “drop in” at your Machine tool.

You want to make certain if the FANUC Servo Motor ’s MOTOR FeedbackEncoder is Faulty or Not.: We can carry out a Health Check of encoder feedback and validate it’s Working. Depending upon the Encoder we can check many characteristics e.g. check Count/ Phase angle/ Z pulse/ Commutating pulses.

You need help in Diagnosing the Real Cause of Servo Errors: ^{Encoder? or Motor? Or Cables? Or Servo Drive? :} In case your Servo installation- FANUC Servo Motor /It’s Encoder/ It’s Drive combo is giving you some trouble and you want to identify the real cause of error. We can help you isolate where the problem is rooted. We can test Encoder feedback independent of your Existing Drive/Controller at your machine. And we can Run Test the FANUC Servo Motor independent of your Drive, We have Universal Drive set up to run virtually any motor.( Current & Available Cables to connect your motor is the limiting factor of course).

You Attempted to Repair FANUC Servo Motor on your own ..detached the Encoder ^{and Now} ^{want to ReAssemble & REAlign it to rotor}^: - You may be attempting to Replace the Bearing or Brake of your FANUC Servo Motor or Motor rewind.. In any such cases it is imperative to detach the fitted encoder from the Rotor shaft. Once detached the encoder needs to be Realigned Again. This Realignment needs special skills and instruments that are available with us.

FANUC Servo Motors are permanent magnet-excited motors with electronic commutation. Servo motors are built like little tanks. The motor housing on these motors are extremely tough and durable. The Majority of Users report that even after Long years of usage, The Only problems the FANUC Servo Motors users ever faced were

- Feedback turning Faulty | Brake Faulty | Bearings Faulty | Connector Broken…of course there could be many other issues that lesser number of users must have faced but We can help you with all the major ones listed above + support you more as below

ü We can check your FANUC Servo Motor by Run Testing it outside Your Machine setup

ü We Check The Health of & Validate Working of FANUC Servo Motor‘s Feedback

ü If the Encoder is Faulty – You can buy New encoder from us.: We have many Encoders/ Resolvers in Stock at Ajman | if we do not have the required encoder then we can arrange that at very short turn around time.

ü Ask us to Replace/ ReAlign / Reprogram “Bought Encoder” on your FANUC Servo Motor

ü We can Run-Test the FANUC Servo Motor to Validate the Encoder Installation.

ü You can also Buy Brake & Get Brake Replacement done on FANUC Servo Motor

We stock brakes from several manufacturers. We of course can’t stock everything so we will arrange the Brake needed for your FANUC Servo Motor from the OEM at shortest possible time.

ü You can also Buy Connectors & Get Connector Replacement Done on FANUC Servo Motor : We have Several type of Motor Power Connectors/ Encoder Connectors in Stock- both in Solder & Crimped contact versions. We have Special tools needed for crimping. We can also build Power Cables/ Encoder feedback Cables for connecting FANUC Servo Motor at your Machine.

ü You may have a Stock FANUC Servo Motor lying on the shelf for Long. You do not know if it is working or not. Ask us to Check.

ü You bought a Used FANUC Servo Motor from someplace .. you want to make certain that the motor is in Working condition. ask FANUC Servo Motor to step in and validate. So you can confidently use the motor on your Machine tool.

There could be any other FANUC Servo Motor situation. you might be grappling with.. let us talk .. we might be of help with our experience and Specialized Inspection instruments.

Encoders/Resolvers for Sale| FANUC Servo Motor Repairs| Feedback ReAlignment & ReProgramming .. Email us at This email address is being protected from spambots. You need JavaScript enabled to view it.

- Need to Replace / Re-Align Encoder Resolver??. Email us: This email address is being protected from spambots. You need JavaScript enabled to view it.

We offer "Test-Diagnose-Repair-Test" Solution - for Fanuc motors/Encoders

We can do Realignment of Encoders/ Resolver or programming and testing of Fanuc Servo Motors. Realignment / Programming and testing is needed when you Replace the Encoder or Re-Install the encoder after dismantling from the motor ( e.g. after bearing replace etc.)

Fanuc Servo Motor Repair Services & Encoder Replacement on Fanuc motors

We can also supply New and Used Encoder for your Fanuc Servo motors