Berger Lahr Servo Motors- Get Tested|Repaired|Encoder-Replaced& ReAligned

Berger Lahr Servo motors fitted with Stegmann Hiperface can now be fixed Right here in Dubai .Do you need encoder replaced and reprogrammed & tested on Servo motor ..yes possible . For example you may have Berger Lahr SER servomotors that are fitted with the absolute sensor system as standard equipment. When using the HIPERFACE® interface between motor-sensor system and device the motor and current controller parameters are internally initialised. This greatly simplifies the commissioning procedure. but commissioning a New Hiperface requires special equipments. We have the right equipment and skills to take care of Motor feedback issues on Berger Lahr motor. If you have any issues with your Berger Lahr Positec SER motor or other motors.. let us talk.

Encoder type Sine/cosine periods per revolution SinCoder SNS50/60 1 or 1024 SinCos SRS50/60 1024, single-turn encoder SinCos SRM50/60 1024, multiturn encoder (4096 revolutions)

We Are Available Right Here in UAE to Help you “Preserve Your Investment” in BERGER LAHR Servo Motors– by Restoring faulty motors to Working condition & Validating Suspected motors by Run-Test

BERGER LAHR Servo Motors are permanent magnet-excited motors with electronic commutation. If you find yourself needing a Repair of your BERGER LAHR Servo Motor . or You need to buy a BERGER LAHR Servo Motor component (e.g. BERGER LAHR Encoders | BERGER LAHR Brake | BERGER LAHR Connectors etc.) Contact us by mail This email address is being protected from spambots. You need JavaScript enabled to view it.

You may utilize our expert servo Repair services in Scenarios where:

You have a BERGER LAHR Servo Motor where you are sure MOTOR FeedbackEncoder is Faulty- We can quickly get you up and running by arranging a New encoder from Stock or Through our Associates around the world, and Replacing it on the motor to get it Working Again. We will Run-Test it so it is ready to “drop in” at your Machine tool.

You want to make certain if the BERGER LAHR Servo Motor ’s MOTOR FeedbackEncoder is Faulty or Not.: We can carry out a Health Check of encoder feedback and validate it’s Working. Depending upon the Encoder we can check many characteristics e.g. check Count/ Phase angle/ Z pulse/ Commutating pulses.

You need help in Diagnosing the Real Cause of Servo Errors: ^{Encoder? or Motor? Or Cables? Or Servo Drive? :} In case your Servo installation- BERGER LAHR Servo Motor /It’s Encoder/ It’s Drive combo is giving you some trouble and you want to identify the real cause of error. We can help you isolate where the problem is rooted. We can test Encoder feedback independent of your Existing Drive/Controller at your machine. And we can Run Test the BERGER LAHR Servo Motor independent of your Drive, We have Universal Drive set up to run virtually any motor.( Current & Available Cables to connect your motor is the limiting factor of course).

You Attempted to Repair BERGER LAHR Servo Motor on your own ..detached the Encoder ^{and Now} ^{want to ReAssemble & REAlign it to rotor}^: - You may be attempting to Replace the Bearing or Brake of your BERGER LAHR Servo Motor or Motor rewind.. In any such cases it is imperative to detach the fitted encoder from the Rotor shaft. Once detached the encoder needs to be Realigned Again. This Realignment needs special skills and instruments that are available with us.

BERGER LAHR Servo Motors are permanent magnet-excited motors with electronic commutation. Servo motors are built like little tanks. The motor housing on these motors are extremely tough and durable. The Majority of Users report that even after Long years of usage, The Only problems the BERGER LAHR Servo Motors users ever faced were

- Feedback turning Faulty | Brake Faulty | Bearings Faulty | Connector Broken…of course there could be many other issues that lesser number of users must have faced but We can help you with all the major ones listed above + support you more as below

ü We can check your BERGER LAHR Servo Motor by Run Testing it outside Your Machine setup

ü We Check The Health of & Validate Working of BERGER LAHR Servo Motor‘s Feedback

ü If the Encoder is Faulty – You can buy New encoder from us.: We have many Encoders/ Resolvers in Stock at Ajman | if we do not have the required encoder then we can arrange that at very short turn around time.

ü Ask us to Replace/ ReAlign / Reprogram “Bought Encoder” on your BERGER LAHR Servo Motor

ü We can Run-Test the BERGER LAHR Servo Motor to Validate the Encoder Installation.

ü You can also Buy Brake & Get Brake Replacement done on BERGER LAHR Servo Motor

We stock brakes from several manufacturers. We of course can’t stock everything so we will arrange the Brake needed for your BERGER LAHR Servo Motor from the OEM at shortest possible time.

ü You can also Buy Connectors & Get Connector Replacement Done on BERGER LAHR Servo Motor : We have Several type of Motor Power Connectors/ Encoder Connectors in Stock- both in Solder & Crimped contact versions. We have Special tools needed for crimping. We can also build Power Cables/ Encoder feedback Cables for connecting BERGER LAHR Servo Motor at your Machine.

ü You may have a Stock BERGER LAHR Servo Motor lying on the shelf for Long. You do not know if it is working or not. Ask us to Check.

ü You bought a Used BERGER LAHR Servo Motor from someplace .. you want to make certain that the motor is in Working condition. ask BERGER LAHR Servo Motor to step in and validate. So you can confidently use the motor on your Machine tool.

There could be any other BERGER LAHR Servo Motor situation. you might be grappling with.. let us talk .. we might be of help with our experience and Specialized Inspection instruments.

Encoders/Resolvers for Sale| BERGER LAHR Servo Motor Repairs| Feedback ReAlignment & ReProgramming .. Email us at This email address is being protected from spambots. You need JavaScript enabled to view it.

Berger Lahr Servo Motors- Get Tested|Repaired|Encoder-Replaced& ReAligned