We are well equipped to Repair/ Realign / Run-Test The digital Indramat motors using resolver feedback
have part numbers beginning with MKD, and MKE. These motors use resolvers for position and commutation feedback in a conventional manner, but they also include a PC board with additional electronics. The additional electronics includes a memory board.
We Can run test these MKE / MKD motors after the resolver be aligned as per the memory data that is contained in the additional electronics.
the Resolver should not be changed by end user because If the alignment is not correct and/or the electronic circuitry is not working properly, the motor will not run correctly on an Indramat drive. Entrust this job to us We will fix it.
We Are Available Right Here in UAE to Help you “Preserve Your Investment” in Rexroth MKD / MKE Servo Motors – by Restoring faulty motors to Working condition.
You may utilize our expert servo Repair services in Scenarios where:
You have a Rexroth MKD / MKE Servo Motor where you are sure Encoder is Faulty- We can quickly get you up and running by arranging a New encoder from Stock or Through our Associates around the world, and Replacing it on the motor to get it Working Again. We will Run-Test it so it is ready to “drop in” at your MKD / MKE hine tool.
You want to make certain if the Rexroth MKD / MKE Servo Motor’s Encoder is Faulty or Not.: We can carry out a Health Check of encoder feedback and validate it’s Working. Depending upon the Encoder we can check many characteristics e.g. check Count/ Phase angle/ Z pulse/ Commutating pulses.
You need help in Diagnosing the Real Cause of Servo Errors: Encoder? or Motor? Or Cables? Or Servo Drive? : In case your Servo installation- Rexroth MKD / MKE Servo Motor/It’s Encoder/ It’s Drive combo is giving you some trouble and you want to identify the real cause of error. We can help you isolate where the problem is rooted. We can test Encoder feedback independent of your Existing Drive/Controller at your MKD / MKE hine. And we can Run Test the Rexroth MKD / MKE Servo Motor independent of your Drive, We have Universal Drive set up to run virtually any motor.( Current & Available Cables to connect your motor is the limiting factor of course).
You Attempted to Repair Rexroth MKD / MKE Servo Motor on your own ..detached the Encoder and Now want to ReAssemble & REAlign it to rotor: - You may be attempting to Replace the Bearing or Brake of your Rexroth MKD / MKE Servo Motor or Motor rewind.. In any such cases it is imperative to detach the fitted encoder from the Rotor shaft. Once detached the encoder needs to be Realigned Again. This Realignment needs special skills and instruments that are available with us.
Rexroth MKD / MKE Servo Motors are permanent magnet-excited motors with electronic commutation. Indramat servo motors are built like little tanks. The motor housing on MKD / MKE motors extremely tough and durable. The Majority of Users report that even after Long years of usage, The Only problems the indramat motors users ever faced were
- Feedback turning Faulty | Brake Faulty | Bearings Faulty |
We can help you with all the above + more as below
ü We can check your Rexroth MKD / MKE Servo Motor by Run Testing it outside Your MKD / MKE hine setup
ü We Check The Health of & Validate Working of Rexroth MKD / MKE Servo Motor‘s Resolvers/Encoder:
ü If the Encoder is Faulty – You can buy New encoder from us.: We have many Encoders/ Resolvers in Stock at Ajman | if we do not have the required encoder then we can arrange that at very short turn around time.
ü Ask us to Replace/ ReAlign / Reprogram “Bought Encoder” on your Rexroth MKD / MKE Servo Motor
ü We can Run-Test the Rexroth MKD / MKE Servo Motor to Validate the Encoder Installation:
ü You can also Buy Brake & Get Brake Replacement done on Rexroth MKD / MKE Servo Motor
We stock brakes from several manufacturers. We of course can not stock everything so we will arrange the Brake needed for your Rexroth MKD / MKE Servo Motor from the OEM at shortest possible time.
ü You can also Buy Connectors & Get Connector Replacement Done on Rexroth MKD / MKE Servo Motor: We have Several type of Motor Power Connectors/ Encoder Connectors in Stock- both in Solder & Crimped contact versions. We have Special tools needed for crimping. We can also build Power Cables/ Encoder feedback Cables for connecting Rexroth MKD / MKE Servo Motor at your MKD / MKE hine.
ü You may have a Stock Rexroth MKD / MKE Servo Motor lying on the shelf for Long. You do not know if it is working or not. Ask us to Check.
ü You bought a Used Rexroth MKD / MKE Servo Motor from someplace .. you want to make certain that the motor is in Working condition. ask Rexroth MKD / MKE Servo Motor to step in and validate. So you can confidently use the motor on your MKD / MKE hine tool.
There could be any other Rexroth MKD / MKE Servo Motor situation. you might be grappling with.. let us talk .. we might be of help with our experience and Specialized Inspection instruments.
Hiperface|EnDat| Mitsubishi| Fanuc|Heidenhain| 1Vpp|Incremental|Serial|Absolut| Hall Effect|…
motor feedback on MKD/ MKE motors are defined by Rexroth in Type code as:
REsolver feedback =G
Resolver Feedback with integrated multiturn absolute Encoder=K
The MKD motors typically use resolver feedback, but according to the manual, they can come with encoder feedback. The MKE motors seem to be environmentally sealed versions of the MKD motors.