We Are Available Right Here in UAE to Help you “Preserve Your Investment” in Nachi (Fujikoshi) Servo Motors– by Restoring faulty motors to Working condition & Validating Suspected motors by Run-Test
We can Run/test Nachi robot motors with Tamagawa Smart ABS serial encoders or The Nachi serial encoders. We have prior intelligence to Run Test | Align Nachin motors fitted with Sumtak Encoder AEC2048 | Tamagawa Encoder MFE0011| Tamagawa Encoder TS5643 | Tamagawa Encoder MFE-0017 |8 pole motors using MFE0011, TS5643, or AEC2048 encoder | 8 pole motors using MFE0017 encoder
We have prior intelligence of RunTest/Align encoders on 8 Pole Servo Motor Nachi MFM452Q5V fitted with Encoder MFE0011 | 8 Pole Servo Motor Nachi MFM452Q6V fitted with Encoder MFE0011 | 8 Pole Servo Motor Nachi MFM552HIV fitted with Encoder AEC2048 | 8 Pole Servo Motor Nachi MFM552Q6V fitted with Encoder MFE0011 | 8 Pole Servo Motor Nachi MFMA452D6V3 fitted with Encoder MFE0017BOMD | 8 Pole Servo Motor Nachi MRM212E1D fitted with Encoder AEC2048 | 8 Pole Servo Motor Nachi MSMA302D7V3 fitted with Encoder MFE0017BOMD
You may utilize our expert servo Repair services in Scenarios where:
You have a Nachi Servo Motor where you are sure MOTOR FeedbackEncoder is Faulty- We can quickly get you up and running by arranging a New encoder from Stock or Through our Associates around the world, and Replacing it on the motor to get it Working Again. We will Run-Test it so it is ready to “drop in” at your Machine tool.
You want to make certain if the Nachi Servo Motor ’s MOTOR FeedbackEncoder is Faulty or Not.: We can carry out a Health Check of encoder feedback and validate it’s Working. Depending upon the Encoder we can check many characteristics e.g. check Count/ Phase angle/ Z pulse/ Commutating pulses.
You need help in Diagnosing the Real Cause of Servo Errors: Encoder? or Motor? Or Cables? Or Servo Drive? : In case your Servo installation- Nachi Servo Motor /It’s Encoder/ It’s Drive combo is giving you some trouble and you want to identify the real cause of error. We can help you isolate where the problem is rooted. We can test Encoder feedback independent of your Existing Drive/Controller at your machine. And we can Run Test the Nachi Servo Motor independent of your Drive, We have Universal Drive set up to run virtually any motor.( Current & Available Cables to connect your motor is the limiting factor of course).
You Attempted to Repair Nachi Servo Motor on your own ..detached the Encoder and Now want to ReAssemble & REAlign it to rotor: - You may be attempting to Replace the Bearing or Brake of your Nachi Servo Motor or Motor rewind.. In any such cases it is imperative to detach the fitted encoder from the Rotor shaft. Once detached the encoder needs to be Realigned Again. This Realignment needs special skills and instruments that are available with us.
Nachi Servo Motors are permanent magnet-excited motors with electronic commutation. Servo motors are built like little tanks. The motor housing on these motors are extremely tough and durable. The Majority of Users report that even after Long years of usage, The Only problems the Nachi Servo Motors users ever faced were
- Feedback turning Faulty | Brake Faulty | Bearings Faulty | Connector Broken…of course there could be many other issues that lesser number of users must have faced but We can help you with all the major ones listed above + support you more as below
ü We can check your Nachi Servo Motor by Run Testing it outside Your Machine setup
ü We Check The Health of & Validate Working of Nachi Servo Motor‘s Feedback
ü If the Encoder is Faulty – You can buy New encoder from us.: We have many Encoders/ Resolvers in Stock at Ajman | if we do not have the required encoder then we can arrange that at very short turn around time.
ü Ask us to Replace/ ReAlign / Reprogram “Bought Encoder” on your Nachi Servo Motor
ü We can Run-Test the Nachi Servo Motor to Validate the Encoder Installation.
ü You can also Buy Brake & Get Brake Replacement done on Nachi Servo Motor
We stock brakes from several manufacturers. We of course can’t stock everything so we will arrange the Brake needed for your Nachi Servo Motor from the OEM at shortest possible time.
ü You can also Buy Connectors & Get Connector Replacement Done on Nachi Servo Motor : We have Several type of Motor Power Connectors/ Encoder Connectors in Stock- both in Solder & Crimped contact versions. We have Special tools needed for crimping. We can also build Power Cables/ Encoder feedback Cables for connecting Nachi Servo Motor at your Machine.
ü You may have a Stock Nachi Servo Motor lying on the shelf for Long. You do not know if it is working or not. Ask us to Check.
ü You bought a Used Nachi Servo Motor from someplace .. you want to make certain that the motor is in Working condition. ask Nachi Servo Motor to step in and validate. So you can confidently use the motor on your Machine tool.
There could be any other Nachi Servo Motor situation. you might be grappling with.. let us talk .. we might be of help with our experience and Specialized Inspection instruments.
Hiperface|EnDat| Mitsubishi| Fanuc|Heidenhain| 1Vpp|Incremental|Serial|Absolut| Hall Effect|…